Adorable Bottle Cap Lady Bug – Handmade Craft Ideas

0
384

By: Heidi Borchers

Bottle cap craft ideas are a fun way to go green and make cute projects on a budget. No need to worry about bugs at this picnic!

Handmade Craft Ideas
Handmade Craft Ideas

 

Materials:
 Plastic caps (I’ve use a Gatorade cap for the body and a water bottle cap for the head)
 Fabric- two different patterns in red (For body and head) and one in black check (for bow)
 Polyester fiberfill
 Glue- I used both the Aleene’s Original Tacky Glue (for a permanent hold) and hot glue ( for the quick hold)
 Cereal cardboard- (one circle for the body and one for the head slightly smaller than the caps)
 Plastic forks- black- 2 for feet
 Plastic spoons-black- 2 for wings
 Candle
 Craft foam-white and black (eyes)
 Paper punches- ¼” and 1/8”
 Decorative wire- black approx. 2” (for mouth)

Instructions:
1. Cut fabric for the large cap (body) and the small cap (head). For the body, cut approximately
1-1/2“larger and for the head, cut approximately 1” all the way around each. Cut a piece of fabric to fit both cardboard circles.

12 Fabulous Picnic Craft Ideas and Restaurant Copycat Recipes-61

 

2. Place the Aleene’s Tacky Glue onto the cardboard circles, and place glue side down on wrong side of fabric.

12 Fabulous Picnic Craft Ideas and Restaurant Copycat Recipes-64

 

3. Cut off the extra fabric around each circle.

12 Fabulous Picnic Craft Ideas and Restaurant Copycat Recipes-65

 

4. Place the Aleene’s Tacky Glue onto top of each lid, place small amount of polyester fiberfill into the glue.

12 Fabulous Picnic Craft Ideas and Restaurant Copycat Recipes-66

 

5. Place small amount of glue onto the center on wrong side of fabric. Place cap with Polyfill, with the Polyfill down into the glue.

12 Fabulous Picnic Craft Ideas and Restaurant Copycat Recipes-68

 

6. Hold this in place and go to next step.

Handmade Craft Ideas
Handmade Craft Ideas

 

7. Place hot glue and the Aleene’s Tacky glue into the center of the inside of cap.

Handmade Craft Ideas
Handmade Craft Ideas

 

8. Immediately push fabric over the edges, over sides of cap, into the center of the glue. Continue around the cap, until all of the fabric is pulled over to inside. If you need more glue to help hold, use a small amount of the hot glue.

Handmade Craft Ideas
Handmade Craft Ideas

 

9. Place both glues onto the back (cardboard side) of the larger fabric covered circle. Put this to the inside of the cap you just covered, with the glue towards the inside. Hold until the hot glue doesn’t feel warm.

Handmade Craft Ideas
Handmade Craft Ideas

 

10. Repeat with the small cap for the head.

12 Fabulous Picnic Craft Ideas and Restaurant Copycat Recipes-75

 

11. Glue the small cap (head) to the large cap (body).

Handmade Craft Ideas
Handmade Craft Ideas

 

12. For the legs, you need the 2 plastic forks. To remove the stem of each fork, hold over a candle flame. As the candle heats the plastic, you can pull the stem from the fork. Remove from the heat. Immediately cut off the stem and trim the warm edges with scissors.

Handmade Crafts and Recycling Ideas
Handmade Crafts and Recycling Ideas

 

13. Glue the forks (feet) to the back side of the body.

Handmade Crafts and Recycling Ideas
Handmade Crafts and Recycling Ideas

 

14. Shown with the feet in place.

Handmade Crafts and Recycling Ideas
Handmade Crafts and Recycling Ideas

 

15. For the wings, you will need 2 plastic spoons. To remove the stem of each spoon, hold over a candle flame. As the candle heats the plastic, you can pull the stem from the spoon.

12 Fabulous Picnic Craft Ideas and Restaurant Copycat Recipes-81

 

16. Cut of the stem, while the plastic is still warm.

12 Fabulous Picnic Craft Ideas and Restaurant Copycat Recipes-83

 

17. Glue wings to the body at the neck. Glue small bow from black check fabric over the top edge of the spoons.

12 Fabulous Picnic Craft Ideas and Restaurant Copycat Recipes-84

 

18. Punch two white circles using the 1/4” paper punch, and two black circles from the 1/8” paper punch. Glue the white circles down first, then black on top of the white. Curve the wire for the mouth, and use a small amount of glue onto the wire and place onto the head, under the eyes. Let dry.